Winterborne Institute logoWinterborne Bicycle Institute Spoke Length Calculator

Spoke geometry · scaled drawings · measurement guide · winterbornestudent.com ↗

Check component measurements, nipple engagement and permitted lacing before ordering.
Enter rim and hub measurements to begin.

Relative tension distribution

Proportional geometry

Axial/radial projection

Wheel-face projection

Calculation definitions

Lateral coordinates are right-positive: left flange z = −WL, right flange z = +WR. Effective lateral distance = |rim-hole z − flange z|. Standard spoke span = ±720° × crosses / total spokes. J-bend length = √[(ERD/2 sin θ)² + (ERD/2 cos θ − PCD/2)² + lateral²] − hole diameter/2.

Straight-pull seat geometry replaces the tangential term with (ERD/2 sin θ − t) and applies no hole-radius subtraction. No material stretch or automatic nipple correction is included. Purchase rounding is nearest increment, not an engagement check.

Advanced uses nearest-grid hole selection and a minimum squared angular-error bijection. Its nominal cross settings do not prove actual physical intersection counts. No spoke interference, valve clearance, assembly over/under order or wheel strength validation is performed.

Measurement reference: FreeSpoke.

Measurement guide

Measure in millimetres. Work through the steps or choose a topic below.

1 · Set up

  1. Identify the rim, hub, spokes, nipples and washers.
  2. Fit the intended end caps. Mark left/right as installed on the bicycle.
  3. Count every hub and rim hole; record rim orientation.
  4. Use metric calipers, suitable diameter/wall-thickness tools and a straightedge.

Hub contact faces are the surfaces touching the frame/fork—not axle tips.

2 · Measure ERD

  1. Measure the inside diameter at two opposite spoke holes: D.
  2. Measure the spoke-bed wall thickness at the first hole: t1.
  3. Measure the thickness at the opposite hole: t2.
  4. Add: D + t1 + t2.

Example: 592 + 2 + 2 = 596 mm.

Opposite means across the rim circumference, not its left/right sidewalls. Measure spoke-bed material, not double-wall rim depth.

t1t2D: inside diameter at spoke bedDiameter input = D + t1 + t2
Measurement diagram, not to scale.

ERD helper

Reference surfaces & nipple allowance

Measure D between hub-facing spoke-bed surfaces; measure each local thickness radially to its nipple-bearing seat. Repeat at other opposite hole pairs.

This sum establishes a nipple-seat diameter. Some makers define ERD at the spoke tips inside the nipples. Check the datum for your nipple/washer setup. No hidden nipple allowance is added; do not count wall thickness twice.

Nipple-seat reference

3 · Measure rim offset

  1. Measure actual outer rim width W.
  2. Locate the centre plane at W/2.
  3. Measure the spoke-hole positions relative to it.
  4. Select centred, single offset bed or independent drilling.

A bed 3 mm left equals independent entries left +3 / right −3. Holes staggered 2 mm outward each side equal left +2 / right +2.

Rim-offset helper

Measure both hole sets from the same LEFT rim face.

Offset formulas & conventions

z = distance from LEFT face − W/2. Right-positive z gives calculator inputs left = −zLeft, right = +zRight. Rim offset is lateral; ERD wall thickness is radial. A symmetrical rim profile may still have staggered holes.

FreeSpoke measurements

4 · Measure a J-bend hub

  1. Measure each flange's spoke-hole PCD, not flange outside diameter.
  2. Use truly opposite holes. Measure centre-to-centre or use the edge helper.
  3. Measure bore diameter at the actual hole, not the chamfer.
  4. Enter left/right PCDs and the bore.

Without an opposed hole pair, use the correct circle geometry or a manufacturer's drawing.

PCD edge helper

PCD formulas & bore correction

Equal round holes, opposed pair: PCD = outside distance − bore, or PCD = inside distance + bore. The J-bend calculation subtracts half the configured bore once. One shared bore input is supported.

Park Tool measurement guide

5 · Measure flange spacing

  1. Measure width between actual dropout-contact faces: W.
  2. Measure left face → left flange centre plane: aL.
  3. Measure right face → right flange centre plane: aR.
  4. Calculate WL = W/2 − aL, WR = W/2 − aR.

Measure both sides. Equal PCDs do not imply equal spacing. Enter rim offset separately.

Centre-to-flange helper

Reference planes

The hub centre is halfway between contact faces, not necessarily at the shell or flange midpoint. Fit the final end caps. Use the J-bend hole centre plane or the defined straight-pull seat plane, not an arbitrary flange surface.

6 · Measure a straight-pull hub

  1. Identify the exact hub, spoke and permitted lacing.
  2. Locate the load-bearing seats from a drawing or correctly seated reference spoke.
  3. Record radial, tangential and axial seat coordinates for each side.
  4. Use them only if they match the model below.

A manufacturer's “spoke offset” is not automatically the app's t coordinate. Separate leading/trailing seats require a matching model.

Seat-coordinate model

Radial = PCD/2; tangential = t, positive clockwise; axial = −WL left, +WR right. This app uses one seat-coordinate set per side and no J-bend bore correction. Confirm that the hub and spoke-length reference fit this model before enabling order sizes.

Straight-pull measuring example · Manufacturer calculator

7 · Enter lacing

  1. Enter total hub holes across both flanges and total rim holes.
  2. Select permitted left/right crosses.
  3. Use Standard for equal counts; Advanced for mismatched-hole assignments.
  4. Review numbered connections and unused holes before assembly.
Advanced conventions

Phase angles run clockwise from the top/valve reference. Half-pitch staggering assumes conventional regular drilling. Advanced matches evenly distributed holes by minimum angular error; it does not check interference, over/under order or structural suitability. Standard shows nominal cross geometry, not a numbered hub-hole map. The nominal span limit is 90°.

8 · Read results

  • Calculated length already includes the configured correction.
  • Purchase size is nearest selected increment; check nipple engagement.
  • Relative tension is a side-average ratio, higher side = 100%, not measured or absolute tension.
  • Each drawing has uniform mm scale; views auto-fit independently.
Calculation and drawing notes

Tension ratios assume uniform average tension per side and balance summed lateral forces; they do not establish local rim equilibrium or a safe target. ERD is not rim outside diameter; PCD is not flange outside diameter. The axial drawing is a projection, not full 3D spoke length. Stroke widths and markers are symbols.

9 · Final check

Helper readings and checkboxes are temporary. Apply measurements before printing.

Report previewCompact build summary

Start a new calculation?

This clears materials and returns measurements and crosses to zero. The purchase-size increment returns to 1 mm.